manualshive.com logo in svg

Siemens VDO DTCO 1381, Technical Description

Share
Download
Siemens VDO DTCO 1381 Technical Description Download Page 141

Service only

Installation of the ADR variant 6.1 DTCO 1381 in vehicles used for the carriage of hazardous goods

Edition 07/2007

Technical Description DTCO 1381

6 - 5

TD00.1381.00 13

2 102

6.1.3 Requirements for the connection of external devices

The connection of external devices to the interfaces (download-, 
remote- or info interface pin D8) of the DTCO 1381 is permissible 
only when these devices fulfil the following requirements:

•

The devices must be switched to a dead (electrical) condition in 
the intended operation (operational case ADR). 

•

The data lines must be installed inside the driver’s com-
partment.

Application default
info interface (pin D8)

Additionally devices for the connection to the info interface (pin D8) 
must have the following electrical characteristics at their input:

Fig. 6 - 1:

Application default info interface (pin D8)

Input for
info interface

External device (ECU)

Evaluation signal

min.1k

Ω

for microcontroller

(pin D8)

max. 10 nF

Attention!

The mentioned requirements for the connection of external devices 
to the interfaces of the DTCO 1381 and the application default for 
the info interface (pin D8) are part of the certificate of conformity 
and must be absolutely kept with the installation in the vehicle.

Summary of Contents for VDO DTCO 1381















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands