Siemens VDO DTCO 1381 Technical Description Download Page 157

Page: 157 / 302

Service only

Preprogramming

7.3 Performing the preprogramming

Edition 07/2007

Technical Description DTCO 1381

7 - 5

TD00.1381.00 13

2 102

7.3

Performing the preprogramming

Definition

Preprogramming of all known or operationally necessary and legally
required parameters.

7.3.1 Legally stipulated parameters

The following parameters are legally stipulated and must be prepro-
grammed:

•

Vehicle identification number

•

Vehicle registration number

•

Country of registration

•

Characteristic coefficient (w-value)

•

Recording equipment constant (k-value)*

•

Effective wheel circumference

•

Tire size

•

Legally permitted maximum speed

•

Odometer reading

•

UTC time

•

Calibration date*

* The DTCO 1381 sets this data automatically.

Attention!

During preprogramming, be absolutely certain that the DTCO 1381
is operated in the specified voltage range!

Summary of Contents for VDO DTCO 1381













































































































































































































































































































Search results

Summary of Contents for VDO DTCO 1381

Reviews:

Brands by name

Popular brands

Siemens VDO DTCO 1381, Technical Description

Search results

Summary of Contents for VDO DTCO 1381

Reviews:

Brands by name

Popular brands