manualshive.com logo in svg

Siemens SIREMOBIL Compact L, Service Instructions Manual, Page: 57 / 86

Share
Download
Siemens SIREMOBIL Compact L Service Instructions Manual Download Page 57

Replacing boards / replacing components

6 - 5

Siemens AG

 

SPR2-130.061.02

Page 5 of 28

SIREMOBIL Compact

Medical Solutions

Rev. 11

09.04

CS PS 24

System Manual

 

SIREPHOS

6

•

Open the SIREPHOS cover (see Chapter 1, "Covers").

•

Remove the laser targeting device, if present.

•

Remove the dose measurement chamber, if present.

•

Remove the collimator.

•

Disconnect the SIREPHOS plug.

•

Remove the ground screw for the protective conductor.

•

Remove the rubber stop of the C-arm on the SIREPHOS side. The screws that secure 
the SIREPHOS are now visible.

•

Remove the SIREPHOS screws. When doing this, have a second person hold the X-ray 
tube unit.

•

Place the new X-ray tube unit on the guide bolts and secure it with both Allen screws. 

•

Ensure that all cables are routed properly.

•

Reconnect the SIREPHOS plug and secure it.

•

Reconnect the protective conductor using the ground screw.

•

Do not install the rubber stop yet.

•

Reinstall the collimator and connect it.

•

Reinstall the dose measurement chamber / laser targeting device and connect them.

•

Perform the kV offset adjustment.

•

Perform the generator adjustment (filament circuit learning program).

•

Ensure that the collimator is functioning properly and is set correctly. 

•

Ensure that the collimator blades are centered in the blanking circle.
- If possible, slightly loosen the Sirephos screws and tilt the SIREPHOS to adjust it.
- Retighten the SIREPHOS screws.

•

Ensure that the collimator blades of the iris diaphragm are visible during fluoroscopy in 
the survey format and zoom format on at least two sides of the monitor image. 

•

Check the display of the blades on the monitor screen and adjust if necessary.

•

Check collimation for direct exposure if there is a cassette holder.

•

Reinstall the rubber stop.

•

Ensure that the area/dose product measurement device is functioning properly 
(if present).

•

Check the dose rate settings and adjust them if necessary.

•

Check the settings of the maximum skin dose rate.

X-ray radiation! 
See Chapter 1, Safety Information.
Protect yourself against radiation exposure. Wear a lead apron.

WARNING

Summary of Contents for SIREMOBIL Compact L























































































Reviews:

No comments