manualshive.com logo in svg

Siemens SIREMOBIL Compact L, Service Instructions Manual, Page: 51 / 86

Share
Download
Siemens SIREMOBIL Compact L Service Instructions Manual Download Page 51

Adjustments / Programs

5 - 29

Siemens AG

 

SPR2-130.061.02

Page 29 of 30

SIREMOBIL Compact

Medical Solutions

Rev. 11

09.04

CS PS 24

System Manual

 

Configuring the MEMOSKOP

5

MEMOSKOP C-E, keyboard emulation

5

There is no keyboard supplied with some SIREMOBIL Compact units and installed 
MEMOSKOP C-E. When replacing the MEMOSKOP C-E or when changing the configu-
ration, the MEMOSKOP service program should be used.

The help file "C-DATA.hlp" will be copied to the service PC during installation of the 
MEMOSKOP service program. The "C-DATA.hlp" help file contains descriptions of the 
programming.

Configuring the video frequency

5

After replacing the MEMOSKOP, it will start at a default video frequency (50 Hz). If the 
monitors were configured for a different frequency, you will have to configure the correct 
video frequency without a "visible image".

With out installed MEMOSKOP keyboard:

•

Use the MEMOSKOP service program to modify the configuration.

With installed keyboard proceed with the steps described below:

•

Invoke Technical Setup on Memoskop (press the CTRL + T keys.)

•

Press the "2" key and press return. The video frequency menu is selected.

•

Depending on the required video frequency, press the right cursor key "->".

"->" = Press the right cursor key

"<-" = Press the left cursor key.

Roadmap K-factor, phase B

Noise suppression, phase B, is programmed in the road-
map mode.
Phase B: Acquisition of fill images.

Roadmap K-factor, phase C

Noise suppression, phase C, is programmed in the road-
map mode. 
Phase C: Acquisition of roadmap images. 

Roadmap Time of phase A

The time of phase A in the roadmap mode is programmed. 
Phase A: Mask acquisition.

"->" pressed 1 time:

60 Hz video frequency 

"->" pressed 2 times:

100 Hz video frequency

"->" pressed 3 times:

120 Hz video frequency

"->" pressed 4 times:

50 Hz video frequency.

Function:

Comments:

Summary of Contents for SIREMOBIL Compact L























































































Reviews:

No comments