manualshive.com logo in svg

Siemens SIREMOBIL Compact L, Service Instructions Manual, Page: 13 / 86

Share
Download
Siemens SIREMOBIL Compact L Service Instructions Manual Download Page 13

Prerequisites

1 - 7

Siemens AG

 

SPR2-130.061.02

Page 7 of 10

SIREMOBIL Compact

Medical Solutions

Rev. 11

09.04

CS PS 24

System Manual

 

Covers

1

Basic system

1

Back cover

Removing the back cover

•

Put on the foot brake.

•

Remove the screws from the back cover.

•

Pull the cover back approx. 25 cm.

•

Unscrew the protective conductor from the cover.

•

Pull the cover completely off and tilt it downward. 

•

Lift up the cover and raise both lateral metal brackets from the guide rails.

Installing the back cover

•

Fit the lateral metal brackets back into the guide rail.

•

Remount the protective conductor to the back cover.

•

Lift the cover and push it forward. Be careful with the EMC spring contact.

•

Replace the cover and tighten the screws.

Monitor trolley

1

Back covers

Removing the covers

•

Remove the upper back cover plate of the log book compartment. 

•

Remove the protective conductor.

•

Remove the lateral Allen screws from the lower back cover. 

•

Remove the protective conductor from the cover.

Installing the covers

•

Begin with the lower back cover.

•

Remount the protective conductor for the lower cover.

•

Install the cover and tighten the screws.

•

Remount the protective conductor for the Logbook cover.

•

Install the cover and tighten the screws.

Electrical voltage!
See Chapter 1, Safety Information.

Disconnect the line voltage plug prior to removing covers.

WARNING

Summary of Contents for SIREMOBIL Compact L























































































Reviews:

No comments