manualshive.com logo in svg

Siemens SIREMOBIL Compact L, Service Instructions Manual, Page: 32 / 86

Share
Download
Siemens SIREMOBIL Compact L Service Instructions Manual Download Page 32

SIREMOBIL Compact

 

SPR2-130.061.02

Page 10 of 30

Siemens AG

System Manual

Rev. 11

09.04

CS PS 24

Medical Solutions

5 - 10

Adjustments / Programs

 

Measurement

5

•

Switch on fluoroscopy.

•

Read and record the value displayed on the dose rate meter.

•

If the value measured exceeds 9 R/min, the maximum tube current must be reduced. 
If the value measured is less than 9 R/min, the tube current does not need to be reduced.

•

Switch fluoroscopy off.

•

Calculate the maximum tube current.

•

Multiply the tube current to be programmed by 10 , since entry on the service PC must be 
made in 1/10mA. Round off the value to the nearest whole number.

Programming

5

•

Connect the service PC to the serial interface of board D1.

•

Select the "Adjustment, Parameters" menu.

•

In the Combo box "Parameter Groups" select "Limitation of skin dose rate (FL)" .

•

Click on "Get from unit" .

•

Enter the value to be programmed in "Value" .

•

Click on "Set Value".

•

Select "Put to unit" . Read the menu guide on the service PC.

•

Select "Save to file".

•

The value to be programmed has been transferred to the SIREMOBIL Compact and 
temporarily stored to the disk.

Checking

5

•

After programming, check the maximum skin dose rate again. 

tube current displayed at 110kV in mA *  9 R/min

= tube current to be programmed in mA

measured dose rate value in R/min

Example: Tube current displayed at 110kV: 5mA

Maximum skin dose rate:

9R/min

Measured dose rate value :

10.2 R/min.

5 (mA) * 9 (R/min)

10.2 (R/min)

= 4.41 (mA)

Rounded to the nearest whole number: 44

The value to be programmed is 44

You must exit the service program with "Logoff" and "Quit". 
Only then will the modified parameters be stored on the floppy 
disk as a new file.

NOTE

Summary of Contents for SIREMOBIL Compact L























































































Reviews:

No comments