manualshive.com logo in svg

Siemens SIREMOBIL Compact L, Service Instructions Manual, Page: 30 / 86

Share
Download
Siemens SIREMOBIL Compact L Service Instructions Manual Download Page 30

SIREMOBIL Compact

 

SPR2-130.061.02

Page 8 of 30

Siemens AG

System Manual

Rev. 11

09.04

CS PS 24

Medical Solutions

5 - 8

Adjustments / Programs

 

•

Select the next level of dose rate (LOW / MID / HIGH) and repeat the dose rate setting for 
the survey and zoom format for this level. 

Concluding steps

5

•

After setting all dose rates for the survey and zoom formats, click "Stop Update" and wait 
until "CAL" disappears from the 7 segment indicator to the right on the operating con-
sole. The TV- iris collimator values are stored to the EE-PROM of the host.

•

Press ESC at the service PC to return to the main menu.

•

Select the "Data, Backup..." menu.

•

Click "Parameter" in the backup window.
- Then click "Backup" .

•

Enter" dose rate set" under "Remarks for Parameter".

•

Then click "OK" . The parameters are stored to disk. 

•

You can now exit from the service program. 

Checking the dose rate in automatic mode 

5

•

Center and reattach the dose measurement chamber to the I.I. input screen. 

•

Set the kV-mA curve HC1 (3 mA plateau curve). If necessary, temporarily program the 
HC1 curve.

•

During automatic mode (kV STOP is off), check the dose rate for dose rate levels
LOW / MID / HIGH for the survey and zoom format.Take into account the correction fac-
tors for the grid and the dose measurement chamber. If necessary, temporarily change 
the dose rate levels and kV-mA curves. 
Tolerance margin for the dose rates: + 15%. 

•

Set the kV-mA curve HC2 (5 mA plateau curve). If necessary, temporarily program the 
HC2 curve. 

•

During automatic mode (kV STOP is off), check the dose rate for dose rate levels 
LOW / MID / HIGH for the survey and zoom format.Take into account the correction fac-
tors for the grid and the dose measurement chamber. If necessary, temporarily change 
the dose rate levels and kV-mA curves. 
Tolerance margin for the dose rates: + 15%.

Checking the dose rate in zoom format with a dose rate measure-
ment chamber that is not completely irradiated may lead to incor-
rect measurements.

NOTE

Summary of Contents for SIREMOBIL Compact L























































































Reviews:

No comments