Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 7

Page: 7 / 188

Installing the machine............................................................................................................72

5.3.1

Safety instructions for installation...........................................................................................72

5.3.2

Preconditions for smooth, vibration-free operation................................................................72

5.3.3

Aligning the machine to the driven machine and mounting (IM B3 / IM B35)........................73

5.3.4

Aligning the machine to the driven machine and attaching it to it (IM B5).............................74

5.3.5

Aligning the machine to the driven machine and attaching it to it (IM V1, IM V10)................75

5.3.6

Axial and radial forces............................................................................................................76

5.4

Connecting the cooling water supply.....................................................................................77

Electrical connection...................................................................................................................................79
6.1

Safety instructions relating to the electrical connection.........................................................79

6.2

Basic rules..............................................................................................................................80

6.3

Terminal box..........................................................................................................................80

6.3.1

Terminal box 1XB1621...........................................................................................................81

6.3.2

Terminal box 1XB1631...........................................................................................................82

6.3.3

Terminal box 1XB7730...........................................................................................................83

6.3.4

Terminal box 1XB7731...........................................................................................................83

6.3.5

Terminal box 1XB7740...........................................................................................................84

6.3.6

Terminal box 1XB7750...........................................................................................................85

6.3.7

Rotating the terminal box.......................................................................................................85

6.3.8

Mounting/removing the terminal box......................................................................................88

6.4

Preparation.............................................................................................................................89

6.4.1

Terminal designation..............................................................................................................89

6.4.2

Selecting cables.....................................................................................................................89

6.4.3

Connecting the grounding conductor.....................................................................................89

6.4.4

Connect metal shield in the terminal box ..............................................................................90

6.4.5

Connection without terminal box............................................................................................91

6.4.6

Connecting the machine for a specific direction of rotation....................................................91

6.5

Inserting and routing the cables.............................................................................................92

6.5.1

Bringing cables into the terminal box 1XB... with sealing insert with break-off ring...............92

6.5.2

Bringing cables into the terminal box 1XB... with cable gland................................................93

6.5.3

Certified cable entries, thread adapters and sealing plugs....................................................94

6.5.4

Laying cables.........................................................................................................................94

6.5.5

Connecting cables with cable lugs.........................................................................................95

6.5.6

Connecting cables without cable lugs....................................................................................96

6.5.7

Use of aluminum conductors..................................................................................................98

6.5.8

Using single-stranded cables.................................................................................................99

6.5.9

Internal equipotential bonding................................................................................................99

6.5.10

Stepless mating face for the seal in the terminal box cover ..................................................99

6.5.11

Minimum air clearances.......................................................................................................100

6.5.12

Finishing connection work....................................................................................................100

6.6

Connecting the auxiliary circuits...........................................................................................101

6.6.1

Selecting cables...................................................................................................................101

6.6.2

Bringing cables into the auxiliary terminal box and routing them.........................................101

6.6.3

Intrinsically safe circuits for sensors or probes....................................................................102

6.6.4

Connect metal shield in the terminal box ............................................................................102

6.6.5

Connecting temperature monitoring for the stator winding..................................................102

6.6.6

Terminating the connection work (auxiliary circuit)..............................................................103

Table of contents

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands