Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 34

Page: 34 / 188

Use either stainless steel or steel (S235JR) for the cooling circuit pipes and fittings.

4.4.2

Pressures and differential pressures in the cooling circuit

The maximum permissible overpressure in the heat sink and thus in the cooling circuit must

not exceed 6 bar.
● If you are using a pump, which reaches more than this maximum pressure, then on the

plant or system side ensure that the maximum pressure is not exceeded.

● The lowest possible differential pressure between the coolant in the supply and return lines

should be selected to allow use of pumps with a flat characteristic. The maximum differential

pressure for a heat sink varies from shaft height to shaft height. Higher pressure differences

significantly increase the risk of cavitation and abrasion.

Machine type

Flow rate ± 10 %

[l/min]

Pressure drop for fresh water

[bar]

1LH….-3A…-….
1MH….-3A…-….

1.0

1LH….-3B…-….
1MH….-3B…-….

1.2

1LH….-4A…-….
1MH….-4A…-….

1.1

1LH….-4B.1.-….
1MH….-4B.1.-….

1.2

1LH….-4B.3.-….
1MH….-4B.3.-….

1.2

1LH….-4B.5.-….
1MH….-4B.5.-….

1.2

1LH….-4B.7.-….
1MH….-4B.7.-….

1.2

● The pressure drop is dependent on the machine type. The machine type is stamped on the

rating plate.

● If there is a risk of frost, use cooling water with antifreeze suitable for this temperature.

The pressure drop increases when antifreeze is added.

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands