Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 77

Page: 77 / 188

5.4

Connecting the cooling water supply

There are three couplings

①

and

②

on the bearing shield for the coolant connection. The

lower coupling

②

is used to drain the coolant for type of construction IM B3.

Figure 5-5

Standard coolant connections and coolant drain hole

1. With the "Piping" option, piping is attached on the right, left or top at the NDE. You can then

connect the coolant supply radially to the appropriate side.

Different threads are available depending on the machine type.

Machine type

Thread

1LH….-3A…-…. / 1MH….-3A…-….
1LH….-3B…-…. / 1MH….-3B…-….

G1/2"

1LH….-4A…-…. / 1MH….-4A…-….
1LH….-4B…-…. / 1MH….-4B…-….

G3/4"

2. Only use valves, fittings and cooling water pipes made of rust-proof, stainless steel in the

cooling system.

3. Make sure that the cooling water complies with the required cooling water specification.
4. Make sure that the appropriate volume of cooling water is available.

Assembly

5.4 Connecting the cooling water supply

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands