Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 44 | Manualshive

Page: 44 / 188

background image

4.16

System-inherent frequencies

NOTICE
System resonances
Excessive vibrations and system resonances can damage the machine set.
● Configure and match the system consisting of the foundation and machine set in such a

way that no system resonances can arise and result in the permissible vibration levels

being exceeded.

● The vibration limit values according to DIN ISO 10816-3 must not be exceeded.

4.17

Torsional load of the drive train

In the event of faults in the electrical connection during operation, excessive air gap torques

can lead to additional mechanical torsional load on the line shaft.

Note
The system planner is responsible for the entire drive train.

WARNING

Torsional loadings of the shaft assembly
If the configuration does not correctly recognize the mechanical torsional loadings of the shaft

assembly, this can lead to serious damage to the machine. This can result in death, serious

injury or material damage.
When planning the system, consider the configuration data.

Note
You can find more information in Chapter 2 of catalog D81.8.

4.18

Transport and storage

Observe the following when carrying out any work on the machine:
● Comply with the general safety instructions
● Comply with the applicable national and sector-specific regulations at the place of

installation

● When using the machine within the European Union, comply with the specifications laid

down in EN 50110‑1 regarding safe operation of electrical equipment.

Preparations for use
4.16 System-inherent frequencies

SIMOTICS FD 1MH1

44

Operating Instructions 08/2017

«
...
42
43
44
45
46
...
»

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Reviews:

No comments

Related manuals for SIMOTICS FD 1LL1

Brand: Canaline Engines Pages: 39

Brand: Club Car Pages: 280

Brand: E-Z-GO Pages: 112

Brand: MTD Pages: 36

Brand: Amico Pages: 47

Brand: GGP Pages: 56

Brand: SCREENLINE Pages: 4

GARDEN SNOWBUSTER (160F)

Brand: Texas Pages: 33

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 16

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 13

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands