Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 55 | Manualshive

Page: 55 / 188

background image

Note
Converter documentation
The operating instructions for the converter are not part of this documentation. Refer also to

the configuration information for the converter.

4.19.5

Insulated bearings when operating the converter

If the machine is operated from a low-voltage converter, insulated bearings are fitted at the

NDE and an insulated encoder with insulated bearings (option).
Comply with the plates on the machine relating to bearing insulation and possible bridges.

①

Driving machine

④

Insulated bearings

②

Motor

⑤

Insulated tachometer fitting

③

Coupling

Figure 4-2

Schematic representation of a single drive

NOTICE
Bearing damage
The bearing insulation must not be bridged. Bearing currents can damage bearings.
● Also for subsequent installation work, such as the installation of an automatic lubrication

system or a non-insulated vibration sensor, make sure that the bearing insulation cannot

be bridged.

● Contact the Service Center, if necessary.

Preparations for use

4.19 Converter operation

SIMOTICS FD 1MH1

Operating Instructions 08/2017

55

«
...
53
54
55
56
57
...
»

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Reviews:

No comments

Related manuals for SIMOTICS FD 1LL1

Brand: GRITAL Pages: 4

FIFTY-FIVE - REV1 11-2007

Brand: NOVAK Pages: 2

Jeep Six-Cylinder

Brand: Golen Pages: 11

Brand: Northern Lights Pages: 42

Brand: GE Pages: 10

Brand: GE Pages: 20

310000 - REVISION C

Brand: GE Pages: 24

Brand: JVL Pages: 367

Brand: SSANGYONG Pages: 16

Brand: SSANGYONG Pages: 42

ClearPath-SCHP Series

Brand: Teknic Pages: 117

NEWTON ACM EUROTITAN CL

Brand: Xl Automatismos Pages: 4

Brand: Marine Power Solutions Pages: 23

Brand: RADEMACHER Pages: 88

Brand: Yanmar Pages: 406

Brand: GAOKIN Pages: 30

Brand: Vanguard Pages: 36

Brand: Honda Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands