Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 110

Page: 110 / 188

7.7

Set values for monitoring the winding temperature

Prior to commissioning

Before running the machine for the first time, set the temperature value for shutdown on the

monitoring device.

Table 7-3

Set value for commissioning

Set value

Temperature

Alarm

145° C

Shutting down

155° C

Normal operation

1. Measure the normal operating temperature T

at the installation location in ° C.

2. Set the values for shutdown and warning corresponding to the operating temperature T

Table 7-4

Set values during normal operation

Set value

Temperature for insulation class 180(H), utilization 155(F)

Alarm

+ 10 K ≤ 145° C

Shutting down

+ 15 K ≤ 155° C

7.8

Test run

After installation or inspection, carry out a test run:
1. Start up the machine without a load. To do this, close the circuit breaker and do not switch

off prematurely. Check whether it is running smoothly.

Switching the machine off again while it is starting up and still running at slow speed should

be kept to a bare minimum, for example for checking the direction of rotation or for checking

in general.

Allow the machine to run down before switching it on again.

2. If the machine is running smoothly and evenly, switch on the cooling equipment. Continue

to observe the machine for a while in no-load operation.

Start-up
7.7 Set values for monitoring the winding temperature

SIMOTICS FD 1MH1

110

Operating Instructions 08/2017

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands