Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 106 | Manualshive

Page: 106 / 188

background image

Cooling
● Check that the machine cooling is available for commissioning.

Cooling water supply
● The cooling water supply is connected and ready for operation.
● The cooling water supply is switched on. The data can be found on the rating plate.
● Cooling water is available in the configured quality and quantity.

● The water cooling is switched on. The data can be found on the rating plate.
● Cooling water of the configured quality is used.

● The bearing insulation should be implemented as shown on the plates.

Electrical connection
● The grounding and equipotential bonding connections have been made correctly.
● The machine is connected so that it rotates in the direction specified.
● Appropriately configured control and speed monitoring functions ensure that the motor

cannot exceed the permissible speeds specified in the technical data. For this purpose,

compare the data on the rating plate or, if necessary, the system-specific documentation.

● The minimum insulation resistance values are within tolerance.
● Minimum air clearances have been maintained.
● Any supplementary motor monitoring devices and equipment have been correctly

connected and are functioning correctly.

● All brakes and backstops are operating correctly.
● At the monitoring devices, the values for "Warning" and "Shutdown" are set.

7.2

Converter operation

The following chapter is relevant only if the machine has been ordered for converter operation.

Note
The order number shows whether the machine was ordered for converter operation. In this

case, digits 1, 2, 3 or 4 is located at the 6th position of the order number.

Start-up
7.2 Converter operation

SIMOTICS FD 1MH1

106

Operating Instructions 08/2017

«
...
104
105
106
107
108
...
»

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Reviews:

No comments

Related manuals for SIMOTICS FD 1LL1

Brand: Evolution Technologies Pages: 12

Diesel Stage 2 Boost Cooler

Brand: Snow Performance Pages: 20

Brand: Bartec Varnost Pages: 48

Brand: Baldor Pages: 1

Brand: Landa Pages: 64

Brand: Dietz Pages: 10

Brand: Dietz Pages: 11

Brand: EX Model Engines Pages: 2

Brand: Nederman Pages: 44

Brand: JVL Pages: 306

Brand: JVL Pages: 347

Brand: Becker Pages: 24

DYNAMIC LINE III

Brand: KEB Pages: 60

Brand: Valach Pages: 24

Brand: O.S. engine Pages: 18

Brand: LONCIN Pages: 23

Brand: LONCIN Pages: 44

Brand: Ingersoll-Rand Pages: 127

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands