Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 137

Page: 137 / 188

9.1.5

General inspection

Check that the installation conditions are observed. We recommend that the following checks

are performed after approx. 16 000 operating hours or at the latest after two years:

Table 9-2

Checks that have to be performed during the general inspection

Checking

When the

motor is

running

At stand‐

still

The electrical parameters are maintained

The permissible bearing temperatures are not exceeded (Page 109)

The smooth running characteristics and machine running noise have not

deteriorated

The motor foundation has no cracks and indentations (*)

The machine is aligned within the permissible tolerance ranges

All the fixing bolts/screws for the mechanical and electrical connections have

been securely tightened

All the potential connections, grounding connections and shield supports are

correctly seated and properly bonded

The winding insulation resistances are sufficiently high

Any bearing insulation is fitted as shown on the plates and labels

The CABLES and insulating parts and components are in good condition

and there is no evidence of discoloring

(*) You can perform these checks while the motor is at standstill or, if required, while running.

NOTICE
Machine damage
When carrying out the inspection, if you detect any impermissible deviations from the normal

state, you must rectify them immediately. They may otherwise cause damage to the machine.

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands