Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 52 | Manualshive

Page: 52 / 188

background image

4.19

Converter operation

The following chapter is relevant only if the machine has been ordered for converter operation.

Note
The order number shows whether the machine was ordered for converter operation. In this

case, digits 1, 2, 3 or 4 is located at the 6th position of the order number.

4.19.1

Converter operation of explosion-proof machines

The operation of the explosion-proof machine on the frequency converter is permitted, when

the specifications for the speed control range and torque characteristic are observed, and if

winding temperature monitoring is ensured via the integrated temperature sensors in

conjunction with a tripping unit.

WARNING

Operation with a converter that is not permissible for the application
If a certain converter type has been defined in the test verification document, on the extra

rating plate, or in the certificate, the machine is only allowed to be operated with this converter.

Death, serious injury, or material damage can result if it is operated with an unauthorized

converter.
● Only operate the motor with the specified converter.

4.19.2

Supply line configuration

NOTICE
Asymmetric voltage load during operation on a TN system in delta connection
An asymmetric voltage load of the machine winding can occur during operation on a TN

system in delta connection with a grounded line conductor. Winding damage can result.
● Do not operate the machine on a TN system with a grounded line conductor.

NOTICE
Ground fault during operation on an IT system
If a ground fault occurs when connected to an IT supply system, the insulation is excessively

stressed. Winding damage can result.
● If possible, complete the process within two hours.
● Rectify the fault cause.
● Deploy a ground fault monitoring.

Preparations for use
4.19 Converter operation

SIMOTICS FD 1MH1

52

Operating Instructions 08/2017

«
...
50
51
52
53
54
...
»

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Reviews:

No comments

Related manuals for SIMOTICS FD 1LL1

Raptor JET SERIES

Brand: Indmar Pages: 82

Brand: Indmar Pages: 94

Brand: Yanmar Pages: 14

Brand: Yanmar Pages: 52

Brand: Yanmar Pages: 66

Brand: Yanmar Pages: 264

Brand: Yanmar Pages: 350

ZAtop SM180.24/B

Brand: ZIEHL-ABEGG Pages: 16

Brand: Volvo Penta Pages: 44

Brand: Volvo Penta Pages: 52

Brand: Volvo Penta Pages: 74

Brand: Volvo Penta Pages: 88

Brand: Valach Motors Pages: 3

Brand: Detroit Diesel Pages: 195

Brand: Honda Pages: 40

Brand: Honda Pages: 42

Brand: Honda Pages: 91

Brand: LONCIN Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands