Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 130

Page: 130 / 188

↓ Grinding noise

↓ Overheating

↓ Radial vibrations

↓ Axial vibrations

Possible causes of faults

Remedial measures

X X Poor alignment

Align the machine set and check the coupling.

Coupled machine not balanced

Rebalance the coupled machine.

X Shocks from coupled machine

Examine the coupled machine.

X X Resonance of the overall system comprising mo‐

tor and foundation

Reinforce the foundation after prior consultation with the

Service Center.

X X Changes in foundation

Determine the cause of the changes and, if necessary,

rectify. Realign the machine.

Reduced air supply, direction of rotation of fan

possibly incorrect

Check the air ducts; clean the machine.

X X Uneven gearbox operation

Resolve any gearbox faults.

Take into account possible changes which may occur during overheating.

Operation
8.12 faults

SIMOTICS FD 1MH1

130

Operating Instructions 08/2017

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands