background image

It  is  of  vital  importance,  before  attempting  to 

operate  your  engine,  to  read  the  general 

'SAFETY  INSTRUCTIONS  AND  WARNINGS' 

section on pages 2-5 of this booklet and to strictly 

adhere to the advice contained therein.

● 

Also,  please  study  the  entire  contents  of  this 

instruction manual, so as to familiarize yourself 

with  the  controls  and  other  features  of  the 

engine.

Keep these instructions in a safe place so that 

you  may  readily  refer  to  them  whenever 

necessary.

It  is  suggested  that  any  instructions  supplied 

with  the  vehicle,  radio  control  equipment,  etc., 

are accessible for checking at the same time.

● 

● 

1

CONTENTS

SAFETY INSTRUCTIONS AND 
WARNINGS ABOUT YOUR O.S. ENGINE

ENGINE CONSTRUCTION, NOTES WHEN 
APPLYING AN ELECTRIC STARTER

18TZ SERIES INSTRUCTIONS

TOOLS, ACCESSORIES, etc.

BASIC ENGINE PARTS, CARBURETOR 
CONTROLS (11K), (11L)

GLOWPLUG, INSTALLATION,
NOTES CONCERNING THE RECOIL STARTER

PRESSURIZED FUEL SYSTEM,
STARTING THE ENGINE & RUNNING-IN 
('Breaking-in)

2-5

6-7

8

11-13

14-16

17-20

FINAL ADJUSTMENT,
CARBURETOR CLEANLINESS

CARE AND MAINTENANCE,
CHECKING THE ENGINE

TROUBLE SHOOTING

ENGINES EXPLODED VIEW &
PARTS LIST

CARBURETOR EXPLODED VIEW  & 
PARTS LIST

O.S. GENUINE PARTS & ACCESSORIES

THREE VIEW DRAWING

38-41

9-10

42-44

24-25

26-29

30-37

21-23

45-48

Summary of Contents for max-18tz series


























Reviews: