Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 76

Page: 76 / 188

Alignment accuracy

The coaxial characteristic of the shafts of electrical machines and driven machine may not

exceed 0.05 mm in diameter.

5.3.6

Axial and radial forces

You can obtain the permissible values for axial and radial forces by contacting the Siemens

Service Center (Page 177) or referring to the machine catalog.

NOTICE
Damage to bearings or the shaft
Large output masses and their centers of gravity outside the shaft extensions can lead to

resonance in operation. This can result in damage to the bearings and shaft.
Ensure that the permissible loads for the forces on the shaft extension are adhered to in

accordance with the catalog data or configuration data.

Note
You can find more information in Chapter 2 of catalog D81.8.

Assembly
5.3 Installing the machine

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands