Siemens SENTRON PAC3200T Product Manual Download Page 77

Page: 77 / 136

Service and maintenance

7.5 Warranty

Equipment Manual, 09/2022, L1V30415168B-03

7.5

Warranty

Procedure

Note
Loss of warranty.

If you open the device, you will invalidate the Siemens warranty. Return faulty or damaged

devices to Siemens.

If the device is faulty or damaged, proceed as follows (only during the warranty period):
1.

Remove the device; refer to section Removal (Page 30).

Pack the device in a suitable manner to prevent it from being damaged during transport.

Return the device to Siemens. You can obtain the address from:

–

Your Siemens sales partner

–

Technical Assistance

Note

The contents of this instruction manual shall not become part of or modify any prior or

existing agreement, commitment, or relationship. All Siemens obligations derive from the

respective sales contract, which also contains the complete and exclusive warranty

agreement. These contractual warranty requirements are neither extended nor restricted by

the implementation of this Operating Manual.

See also

Latest information (Page 8)

Summary of Contents for SENTRON PAC3200T









































































































































Search results

Summary of Contents for SENTRON PAC3200T

Reviews:

Siemens SENTRON PAC3200T, Product Manual, Page: 77 / 136

Search results

Summary of Contents for SENTRON PAC3200T

Reviews: