Siemens SENTRON PAC3200T Product Manual Download Page 19

Page: 19 / 136

Description

2.2 Measuring inputs

Equipment Manual, 09/2022, L1V30415168B-03

Connection type

Measured variable

Avail.

3P4W

Avail.

3P3W

Avail.

3P4WB

Avail.

3P3WB

Avail.

1P2W

Apparent power L

✓

—

Apparent power L

✓

—

Active power L

✓

—

✓

—

✓

Active power L

✓

—

Active power L

✓

—

Reactive power L

(Q1)

✓

—

✓

—

✓

Reactive power L

(Q1)

✓

—

Reactive power L

(Q1)

✓

—

Power factor L

✓

—

✓

—

✓

Power factor L

✓

—

Power factor L

✓

—

THD voltage L

✓

—

✓

—

✓

THD voltage L

✓

—

THD voltage L

✓

—

THD current L

✓

THD current L

✓

—

THD current L

✓

—

Frequency

✓

Medium voltage L-N

✓

—

Medium voltage L-L

✓

—

✓

—

Medium current

✓

—

Total apparent power

✓

Total active power

✓

Total reactive power (Q1)

✓

Total power factor

✓

Amplitude unbalance voltage

✓

—

Amplitude unbalance current

✓

—

Cumulated active power import (current period)

✓

Cumulated reactive power import (current period)

✓

Cumulated active power export (current period)

✓

Cumulated reactive power export (current period)

✓

Active energy import (current period)

✓

Reactive energy import (current period)

✓

Active energy export (current period)

✓

Reactive energy export (current period)

✓

Total active energy import (tariff 1) (current period)

✓

Total active energy import (tariff 2) (current period)

✓

Total reactive energy import (tariff 1) (current period)

✓

Total reactive energy import (tariff 2) (current period)

✓

Total active energy export (tariff 1) (current period)

✓

Total active energy export (tariff 2) (current period)

✓

Total reactive energy export (tariff 1) (current period)

✓

Total reactive energy export (tariff 2) (current period)

✓

Total active energy import T1+T2 (current period)

✓

Total active energy export T1+T2 (current period)

✓

Summary of Contents for SENTRON PAC3200T









































































































































Search results

Summary of Contents for SENTRON PAC3200T

Reviews:

Siemens SENTRON PAC3200T, Product Manual, Page: 19 / 136

Search results

Summary of Contents for SENTRON PAC3200T

Reviews: