manualshive.com logo in svg

Siemens SENTRON PAC3200T, Product Manual, Page: 31 / 136

Share
Download
Siemens SENTRON PAC3200T Product Manual Download Page 31

 

 
Equipment Manual, 09/2022, L1V30415168B-03 

29

 

Mounting

 

3 

3.1

 

Introduction 

 

 

WARNING 

The use of damaged devices may result in death, serious injury, or property damage. 

Do not install or start up damaged devices. 

 

Installation location 

The PAC3200T device is mounted on a TH35 rail (complying with EN 60715) and is intended 

for installation in permanently installed systems within closed rooms. 
The measuring device can be mounted in any position. The device can be mounted in a 

horizonal or in a vertical position. For ergonomic reasons, we recommend mounting the 

device horizontally at the user's eye level. 

 

 

Note 
Avoid condensation. 

Sudden fluctuations in temperature can lead to condensation. Condensation can affect the 

function of the device. Store the device in the operating room for at least 2 hours before 

commencing installation. 

 

Summary of Contents for SENTRON PAC3200T









































































































































Reviews:

No comments