Siemens SENTRON PAC3200T Product Manual Download Page 44

Page: 44 / 136

Connection

4.4 Connecting the Ethernet communication cable

Equipment Manual, 09/2022, L1V30415168B-03

4.4

Connecting the Ethernet communication cable

Always use a shielded cable for the Ethernet data cable.
1.

Plug the RJ45 cable connector into the RJ45 device socket until the connector engages in

the socket.

Provide sufficient mechanical strain relief for the Ethernet cable.

Ground the shield of the cable (see chapter Grounding of the Ethernet communication cable

(Page 42)).

4.4.1

Grounding for Ethernet

When using industrial LAN cables, corresponding strain relief must be provided.

NOTICE
Ethernet cables must be grounded.

The upper limit values will be exceeded if the cable is not grounded.

Compliance with the technical limit values for noise radiation and noise immunity is only

guaranteed if the cable is correctly grounded. The operator of the system is responsible for

ensuring compliance with the statutory limit values (CE mark). Make a shield connection as

described here.

Summary of Contents for SENTRON PAC3200T









































































































































Search results

Summary of Contents for SENTRON PAC3200T

Reviews:

Siemens SENTRON PAC3200T, Product Manual, Page: 44 / 136

Search results

Summary of Contents for SENTRON PAC3200T

Reviews: