manualshive.com logo in svg

Siemens SENTRON PAC3200T, Product Manual, Page: 51 / 136

Share
Download
Siemens SENTRON PAC3200T Product Manual Download Page 51

 

Operation 

 

5.3 Protection against manipulation 

 
Equipment Manual, 09/2022, L1V30415168B-03 

49

 

5.2.3

 

Web server 

The device can be read out with a PC/notebook via a website using the web server integrated 

in the device. Communication takes place via HTTP. 
The web server provides the following functions: 
•

 

Device information such as serial number, firmware status etc. 

•

 

Measured value view 

•

 

Energy values can be downloaded as CSV file. 

 
Start web server: 
1.

 

Connect the device to the PC or network via the Ethernet interface. 

2.

 

Make sure that the PAC2200 and the configuration computer are in the same subnet. 

3.

 

Enter the IP address of the device in the browser. 

 
HTTP port: 80 (default setting) 
 

 

 

Note 

The web server can be deactivated with the HTTP Port: 0 setting. 

 

5.3

 

Protection against manipulation 

5.3.1

 

Introduction 

The PAC3200T is equipped with a range of mechanisms to protect against deliberate and 

inadvertent device manipulation. 
•

 

Password protection 

•

 

Hardware write protection 

•

 

IP filter 

•

 

Configurable Modbus TCP port 

•

 

Configurable HTTP port 

•

 

Housing seal and sealing 

Summary of Contents for SENTRON PAC3200T









































































































































Reviews:

No comments