manualshive.com logo in svg

Siemens SENTRON PAC3200T, Product Manual, Page: 12 / 136

Share
Download
Siemens SENTRON PAC3200T Product Manual Download Page 12

Introduction 

 

1.4 Open Source Software 

 

 

10

 

Equipment Manual, 09/2022, L1V30415168B-03 

1.4

 

Open Source Software 

This product, solution or service ("Product") contains third-party software components. These 

components are Open Source Software licensed under a license approved by the Open 

Source Initiative or similar licenses as determined by SIEMENS ("OSS") and/or commercial or 

freeware software components. With respect to the OSS components, the applicable OSS 

license conditions prevail over any other terms and conditions covering the Product. The OSS 

portions of this Product are provided royalty-free and can be used at no charge.  
If SIEMENS has combined or linked certain components of the Product with/to OSS 

components licensed under the GNU LGPL version 2 or later as per the definition of the 

applicable license, and if use of the corresponding object file is not unrestricted ("LGPL 

Licensed Module", whereas the LGPL Licensed Module and the components that the LGPL 

Licensed Module is combined with or linked to is the "Combined Product"), the following 

additional rights apply, if the relevant LGPL license criteria are met: (i) you are entitled to 

modify the Combined Product for your own use, including but not limited to the right to 

modify the Combined Product to relink modified versions of the LGPL Licensed Module, and 

(ii) you may reverse-engineer the Combined Product, but only to debug your modifications. 

The modification right does not include the right to distribute such modifications and you 

shall maintain in confidence any information resulting from such reverse-engineering of a 

Combined Product.  
Certain OSS licenses require SIEMENS to make source code available, for example, the GNU 

General Public License, the GNU Lesser General Public License and the Mozilla Public License. 

If such licenses are applicable and this Product is not shipped with the required source code, a 

copy of this source code can be obtained by anyone in receipt of this information during the 

period required by the applicable OSS licenses by contacting the following address:  
Siemens AG  

Smart Infrastructure 

Electrical Products  

Technical Support  

Postfach 10 09 53  

93009 Regensburg 

Germany 
You will find Technical Support under. 
Keyword: Open Source Request (please specify Product name and version, if applicable)  
SIEMENS may charge a handling fee of up to 5 EUR to fulfil the request.  

Summary of Contents for SENTRON PAC3200T









































































































































Reviews:

No comments