Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 49

Page: 49 / 83

Programming

PXL Conventional Fire Alarm Control Panel

SET AC FAIL SIGNAL DELAY

- Underwriters Laboratories, Inc.

requires all fire protection systems which communicate to a Central

Station or report as a Remote Station to delay the transmission of AC

Fail Trouble Signals by a predetermined length of time. The system

default is a 6 hour delay which is used for Central Station. For Remote

Station, use the 15 hour delay. The "no delay" option is used for local

fire alarm.

ALARM VERIFICATIONS

- This History selection allows the user to

view any alarm verified zones which went through an alarm verifica-

tion cycle and did not result in an alarm.

ASC AUTOMATIC SYSTEM CONFIGURATION

- This System

mode performs automatically when the System is turned on for the

first time. The PXL first polls all the modules to determine the num-

ber of each type and their addresses. The user is then asked

YOU WANT TO CONFIGURE THE SYSTEM NOW?

Answering

sends

the system into its normal operating mode where all new circuits

operate in default program mode.
Answering

YES

starts the Automatic System Configuration program-

ming of the System. ASC leads the user through the different pro-

gramming functions. The default values of all programmable features

are displayed and the user has the opportunity to change each on

If no selection is made during the ASC routine, the screen will time

out in 20 minutes and start its normal operating mode with all func-

tions operating in default program mode.
When a new module(s) is added to a system that is in operation, the

ASC routine will run on startup. The user will again be asked

DO YOU

WANT TO CONFIGURE THE SYSTEM NOW?

Answering

sends the

system into its normal operating mode. All previous configurations

operate as before; all new modules operate in default mode.

NOTE:

The user

must

view every zone to insure the integrity of

zone operation. At the end of the Automatic System Con-

figuration mode, the system automatically resets and all

program inputs are stored to memory.

CONTROL

- This menu selection allows the user to bypass System

circuits or to test outputs.

DELETE MODULES

- This Program selection allows the user to

confirm that modules have physically been removed from the sys-

tem. When previously installed modules are no longer reporting to

the PXL, the System annunciates a

Module No Response

trouble

condition.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands