Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 41

Page: 41 / 83

Operation

PXL Conventional Fire Alarm Control Panel

Figure 21

The PCM-1 User Interface

3 Operating the PXL Control Panel

INTRODUCTION

The PXL System contains many software-based features. These

features are accessible through the user interface on the PCM-1

which is located on the front of the unit (See Figure 21). The user

interface is password protected and menu driven. It allows the user

to enter all software-selectable options. The user interface has a 4

line by 20 character LCD display which maps functions to 8 keys.

The interface also includes a 12 button alphanumeric keypad for

special programming functions.
The PCM-1 has the following 6 system status LEDs:

Power

Trouble

Alarm

Audibles Silenced

Supervisory

Partial Disable

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands