Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 5

Page: 5 / 83

Contents

PXL Conventional Fire Alarm Control Panel

iii

Illustrations

1. Basic PXL System............................................................................................. 2

2. The PSE-1 Enclosure ....................................................................................... 7

3. Removing the PMK-1 Bracket from the PSE-1 ................................................. 8

4. PPS-10M Module Board ................................................................................. 10

5. Sliding the PPS-10M into the PMK-1 Bracket ................................................. 11

6. Mounting the PPS-10M on the PMK-1 Bracket ............................................... 11

7. PRM-4 Module Board...................................................................................... 12

8. Mounting the PRM-4 on the PMK-1 Bracket ................................................... 13

9. PNC-2Z Module Board .................................................................................... 14

10. Mounting the PNC-2Z on the PMK-1 Bracket ................................................. 15

11. Mounting the PCM-1 on the PMK-1 Bracket ................................................... 18

12. Labeling the Zones and Terminal Blocks on the PCM-1 ................................. 18

13. PZE-4B Module Board .................................................................................... 20

14. Mounting the PZE-4B ...................................................................................... 20

15. Labeling the Zones and Terminal Blocks on the PZE-4B ................................ 20

16. Installing the PMK-1 Bracket in the PSE-1...................................................... 22

17. Mounting the PTX-12 ...................................................................................... 23

18. Installing the Grounding Strap with Two Lugs ................................................. 24

19. Installing the Grounding Strap with One Lug .................................................. 25

20. PXL Power Limited Wiring .............................................................................. 28

21. The PCM-1 User Interface .............................................................................. 35

22. PXL Automatic System Configuration Mode ................................................... 40

23. PXL Normal Operating Mode .......................................................................... 42

24. Line Graph of Alarm Verification ..................................................................... 49

25. PPS-10M Wiring for Canadian Automatic Battery Disconnect ........................ 68

Appendix C ......................................................................................67

Configuring and Programming the PXL Fire Alarm System for
Use in Canada ...................................................................................................67

Appendix D ......................................................................................69

Silent Knight 5128/5129 Digital Fire Communicator Connected

to the PXL Control Panel Reporting PXL Control Panel Conditions

to a Central Station or PXL as a Remote Supervising Station Fire Alarm

System ...............................................................................................................69

Appendix E ......................................................................................73

Wiring in an Expanded System (PSE-2 Enclosure) .......................................73

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands