Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 75

Page: 75 / 83

Appendix D

PXL Conventional Fire Alarm Control Panel

APPENDIX D

Silent Knight Model 5128/5129 Digital Fire

Communicator Connected to the PXL

Control Panel Reporting PXL Control Panel

Conditions to a Central Station or PXL as a

Remote Surpevising Station Fire Alarm

System

OPERATION

The PXL reports system conditions using the Silent Knight Model

5128/5129, a four channel digital communicator that reports alarm,

trouble, supervisory, and miscellaneous status. When used with the

PXL, the Silent Knight Model 5128/5129 uses the alarm, trouble, and

supervisory channels. The miscellaneous status channel may be

used to annunciate conditions other than fire.

INSTALLATION

Remove all system power before installation, first battery and

then AC.

(To power up, connect the AC first and then the battery.)

Mounting

Silent Knight Model 5128

Mount the Silent Knight Model 5128 within the PXL enclosure as

shown in Figure 26. When mounting the unit in either the PSE-1 or

PSE-2 enclosure, place the Silent Knight Model 5128 between the

knockouts on the top of the right-hand side of the panel. Alternate

mounting for the Silent Knight 5128 may include double-sided tape,

velcro, or snaptrack.

Silent Knight Model 5129

The Silent Knight Model 5129 must be mounted outside of the PXL

enclosure and within 20 feet of it. All electrical wiring must be in metal

conduit.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands