Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 35

Page: 35 / 83

Installation

PXL Conventional Fire Alarm Control Panel

TABLE 6

NON-POWER LIMITED WIRING

Module

Termination

Enclosure

Knockout

PPS-10M

PRM-4

TB1 (3 positions)
TB6 (All 9 positions)
TB1 (6 positions)
TB2 (6 positions)

7
4
4
4

WIRING IN ENCLOSURE

Non-Power Limited Wiring

The following wiring is considered non-power limited:

from the PTX-12 transformer to PPS-10M, TB1

from the batteries to PPS-10M, TB2 (wiring routed behind trans-

former)

from PPS-10M, NAC power (TB2) to optional PNC-2Z, TB1

To maintain the required separation, the wires must be routed and

held in place by a separate tie-down to lances located on the rear of

the enclosure. See Figure 20 for the location of the lances.

WIRING ENTERING ENCLOSURE

Power Limited Wiring

Wiring to the following PXL module terminations is considered power

limited and must enter the enclosure through the knockouts specified

in Table 7 (Refer to Figure 20). Wiring between the knockout speci-

fied and the module termination must be in the shortest route and

must not overlap any other wiring.

TABLE 7

POWER LIMITED WIRING

Module

Termination

Enclosure

Knockout

PCM-1
PNC-2Z

PPS-10M

PZE-4B

All Zone Wiring
TB2 (All positions)
TB3 (All positions)
TB3 (2 positions)
TB4 (All 16 positions)
TB5 (1-4)
All Zone Wiring

1 and 2

3
3
6
6
6

1 and 2

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands