Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 27

Page: 27 / 83

Installation

PXL Conventional Fire Alarm Control Panel

The installation kit consists of the following items:

ITEM

PART NUMBER

QUANTITY

plastic bezel

195-293693

power/data cable

555-194066

3.9K, 1/4W, EOL resistor

140-820186

zone label

575-194072

4-position terminal block

150-094071

#6 x 3/8 Phillips screws

906-220606

Mounting the PZE-4B

Refer to Figure 14 to mount the PZE-4B module to the PMK-1

mounting bracket.

NOTE:

The PCM-1 must be installed before mounting and wiring

the PZE-4B Zone Expander.

NOTE:

If the PZC-4D is used to convert the system to Class A,

refer to the

PZC-4D Installation Instructions,

P/N 315-

094164, before installing the PZE-4B.

1. a. Complete the zone label with the appropriate zone

description (Refer to Figure 15).

For example:

Floor 1, East Wing

Floor 1, West Wing

Slip the label under the overlay so the information shows

through.

b. Fill in the terminal block label with the appropriate zone

information.

2. Place the bezel in the appropriate position on the PMK-1

mounting bracket (Refer to Figure 14). Be sure that the locating

pin on the bezel goes through the hole in the bracket. Secure in

place using the screws provided in the mounting holes in upper

corners of the bezel.

3. Connect the terminal blocks at the top of the IDC zone bezels so

that the blocks are facing up.

Install Interconnecting Cable

To complete the PZE-4B internal wiring connections, plug the power/

data cable, P/N 555-194066, from JP7 of the PZE-4B to JP6 of the

PCM-1. Note that the connection is made on the back of the printed

circuit board.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands