Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 63

Page: 63 / 83

Testing and Troubleshooting

PXL Conventional Fire Alarm Control Panel

TROUBLE MESSAGES (Cont.)

Trouble Message Text

Condition

Possible Cause

PCM MOD O WATCHDOG

PCM module watchdog

Module locked up; reset the panel

PNC MOD X MULTI/UNKN

PNC not responding and ASC
routine will not run

Two or more PNC modules installed with
same dipswitch address

PNC MOD X NO RESPONSE

PNC not responding

• Module removed from system*
• Module failed
• Module address changed

PNC MOD X NOT SPEC’D

PNC responding but not in
configuration

• PNC module added but system not
reconfigured
• PNC module address changed

PNC MOD X WATCHDOG

PNC module watchdog

Module locked up; reset the panel

PNC MOD X COMM ERR

PNC communication error

• Data transmission failure
• Module failed

PPS MOD X COMM ERR

PPS communication error

• Data transmission failure
• Module failed

PPS MOD X NO RESPONSE

PPS not responding

• Module removed from system*
• Module failed
• Module address changed

PPS MOD X NOT SPEC’D

PPS responding but not in
configuration

• PPS module added but system not
reconfigured
• PPS module address changed

PPS MOD X WATCHDOG

PPS module watchdog

Module locked up; reset the panel

PPS1 AUX PWR FAULT

Auxiliary power trouble on first
PPS-10M in PXL System

Aux power fuse blown

PPS1 BATTERY FAULT

Battery trouble on first PPS-10M in
PXL System

• Battery missing/not connected
• Battery high
• Battery low
• Battery fuse blown
• Battery connected backwards

PPS2 AUX PWR FAULT

Auxiliary power trouble on second
PPS-10M in PXL System

Aux power fuse blown

PPS2 BATTERY FAULT

Battery trouble on second
PPS-10M in PXL System

• Battery missing/not connected
• Battery high
• Battery low
• Battery fuse blown
• Battery connected backwards

PRM MOD X COMM ERR

PRM communication error

• Data transmission failure
• Module failed

PRM MOD X MULTI/UNKN

PRM not responding and ASC
routine will not run

Two or more PRM modules installed with
same dipswitch address

* Modules purposely removed from the system may be removed from the configuration using
the "Delete Module Option" in the Program menu.

X = Module number

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands