Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 42

Page: 42 / 83

PXL Conventional Fire Alarm Control Panel

Operation

OPERATION

The PXL annunciates the following modes:

Alarm
Supervisory
Trouble
Normal

Alarm

The PXL Display board lights the appropriate red zone alarm LED

and the general ALARM LED to indicate to the user that an Alarm

condition exists. The following screen is displayed on the PXL:

ALARM 1 OF 1:

LOCATION

ACKNOWLEDGE ALARMS>

NOTE:

The PXL can record and display up to 5 zone alarms prior to reset.

Supervisory

A Supervisory alarm condition is indicated on the PXL by the lighted

SUPERVISORY LED and the appropriate zone LEDs. The following

screen is displayed on the PXL:

SUPV 1 OF 1:

LOCATION

ACKNOWLEDGE SUPV’S>

Trouble

A Trouble condition is displayed by a lighted TROUBLE LED along

with the appropriate LEDs corresponding to the zone in trouble. The

following screen is displayed on the PXL:

TROUBLE 1 OF 1:

LOCATION

ACKNOWLEDGE TRBL’S>

For a description of the system trouble messages, see

Trouble

Messages

, page 56.

Normal

The Normal Mode is the absence of any alarm, supervisory, or

trouble condition. The

POWER

LED is lit in Normal mode when the

system has AC power. The

Alarm, Trouble, Supervisory, Audibles

Program

- Program

- Test

- Control

- History

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands