Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 12

Page: 12 / 83

PXL Conventional Fire Alarm Control Panel

Installation

4. Install any optional PRM-4 relay modules.
5. Install any optional PNC-2Z Notification Appliance Circuit

modules.

6. Install power/data interconnect cable between modules on lower

level of bracket as well as the power/data interconnect cable for

the modules on the upper level of the mounting bracket.

7. Install the PCM-1 Main Control module.
8. Plug in the power/data interconnect cable from the PPS-10M

board and from PCM-1.

9. Install any optional PZE-4B zone expander modules.

Install interconnecting cables.

10. Install the PMK-1 module bracket in the PSE-1 enclosure.
11. Install the PTX-12 transformer.
12. Install the grounding straps
13. Check field wiring.
14. Install field wiring (including the main power connections). Refer

to the PXL Connection Diagram at the end of the manual.

15. Install all system labels.
16. Install the door to the backbox.
17. Power-up the PXL.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands