Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 16

Page: 16 / 83

PXL Conventional Fire Alarm Control Panel

Installation

Mounting the PPS-10M to the PMK-1 Bracket

1. First, slide the PPS-10M module board down through the

opening slot in the PMK-1 mounting bracket with the terminal

blocks facing out, as shown in Figure 5.

2. Then reverse direction and slide the PPS-10M upward so that the

locating tabs protrude through the slots of the bracket, as shown

in Figure 6.

3. Fasten the board to the mounting bracket in three places using

the screws provided (See Figure 6).

Figure 4

PPS-10M Module Board

NOTES:

When two Model PPS-10M power supplies are used in a PXL System:
1. Cut Jumper JP3 on the second PPS-10M.
2. Disable TB5 on the second PPS-10M.
3. Cut and remove the red wires from the 15" cable in the PCK-1 kit

(P/N 500-695066) when connecting between the two PPS-10Ms.

4. Refer to Appendix E for cabling connections in a PSE-2 Enclosure.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands