Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 73

Page: 73 / 83

Appendix C

PXL Conventional Fire Alarm Control Panel

APPENDIX C
Configuring and Programming the PXL

Fire Alarm System for Use in Canada

Module Configuration

The following restrictions on firmware revisions apply:

PCM-1 module must include PXL Revision 3.0 or higher firm-

ware and PCM/PZE Revision 3.0 or higher firmware.

PZE-4B modules must include PCM/PZE Revision 3.0 or higher

firmware.

PPS-10M modules must include PPS Revision 2.0 or higher

firmware.

LED-3/-4 annunciators must include revision 2.0 or higher

firmware.

There are no restrictions on firmware revisions for the following:

PNC-2Z modules
PRM-4 modules
RSA series annunciators

Programming the PXL

Whether programming the System from the Automatic System

Configuration routine or in the Program Mode accessible from the

Main Menu, the Country Code must be set for Canada. This will

cause the first alarm, supervisory, or trouble condition to be continu-

ously reported on the Liquid Crystal Display. Subsequent alarms will

be stored in a queue and can be accessed through the review screen.
The Canada Country Code selection will also cause supervisory

conditions to latch until System reset. All other programming options

follow the instructions in Section 4 (Programming) of this manual.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands