ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 33

Page: 33 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

LED Indicator

The LED indicator is located on the base, Table 4.4 lists the status description.

Table 4.4 LED indicator description

Status

Description

Green On

Dobot Magician works normally

Yellow On

Dobot Magician is in the starting status

Blue On

Dobot Magician is in the offline mode

Blue Blinking

Dobot Magician is running homing procedure or auto levelling

Red On



Dobot Magician is at the limited position



Alarm is not cleared



Connection of 3D printing kit is abnormal

Multiplexed I/O Interface Description

The addresses of the I/O interfaces in Dobot Magician are unified. Most of I/O interfaces have

multiple functions, to control the peripheral equipment.

Multiplexed Base I/O Interface Description

4.3.1.1

Multiplexed UART Interface Description

Figure 4.3 shows the UART interface on the base, Table 4.5 lists the multiplexed I/O

description.

Figure 4.3 UART interface

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands