ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 70

Page: 70 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

NOTICE

The imported image should be placed within the annular area on the

Write & Draw

page,

as shown in Figure 5.59. If not, the robotic arm reaches its limited position and thus

cannot engrave on an object. In this case, the image is highlighted with a red border, as

shown in Figure 5.60.

Figure 5.59 The PLT or SVG image is located within the annular area

Figure 5.60 The PLT or SVG image is located outside the annular area



Click

Open

on the

Write & Draw

page to import a built-in PLT or SVG image file from

the DobotStudio installation directory

InstallatonDirectory

\DobotStudio\config\prefab\system\source

, as shown in Figure

5.61. You can also import your custom PLT or SVG image file.

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands