ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 26

Page: 26 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide



The direction of Y-axis is perpendicular to the base leftward.



The direction of Z-axis is vertical upward, which is based on the right hand rule.



The R-axis is the attitude of the servo center relative to the origin of the robotic arm,

of which the positive direction is counter-clockwise. The R-axis only exists once the

end-effector with servo is installed.

Motion Function

The motion modes of Dobot Magician include Jogging, Point to Point (PTP), ARC.

3.3.3.1

Jogging Mode

Jogging mode is the mode jogging Dobot Magician along the Cartesian coordinate system or

Joint coordinate system when teaching.



NOTE

This topic describes jogging mode by the GUI operation of DobotStudio.



Cartesian coordinate system mode



Click

X+

X-

and Dobot Magician will move along X-axis in the negative or positive

direction.



Click

Y+

Y-

and Dobot Magician will move along Y-axis in the negative or positive

direction.



Click

Z+

Z-

and Dobot Magician will move along Z-axis in the negative or positive

direction.



Click

- and Dobot Magician will rotate along R-axis in the positive or negative

direction.

NOTICE

If the end-effector with servo is installed on the Dobot Magician, the R-axis will move

together with Y-axis, to make sure that the terminal posture relative to the origin stays

constant.



Joint coordinate system mode



Click

- and control the base motor to rotate in the negative or positive

direction.



Click

- and control the Rear Arm motor to rotate in the negative or positive

direction.



Click

- and control the Forearm motor to rotate in the negative or positive

direction.



Click

- and control the servo to rotate in the negative or positive direction.

3.3.3.2

Point to Point (PTP)

PTP mode supports MOVJ, MOVL, and JUMP, which means point to point movement. The

trajectory of playback depends on the motion mode.

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands