ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 135

Page: 135 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

130

Figure 5.158 Auto levelling result

Homing

Dobot Magician has been calibrated before being shipped out. If the Dobot Magician has been

hit or the motor has lost step, leading data abnormal, you need to operate homing to improve the

positioning accuracy.

Prerequisites



Dobot Magician has been powered on.



Dobot Magician has been connected to DobotStudio successfully.

Procedure

Click

Home

on the DobotStudio page, as shown in Figure 5.159.

NOTICE



Please remove the end-effector from the Dobot Magician before homing.



Please ensure that there are no obstacles in the workspace during homing.

Figure 5.159 Operate homing

Dobot Magician will rotate clockwise to the limited position and then return to the default

homing point automatically and the LED indicator on the base turns blue and is blinking. After the

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands