ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 49

Page: 49 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide



NOTE

After reading the beginner guide of the DobotStudio, click

to close it.

Put a small cube on the work surface near the suction cup kit.

Select the

MOVJ

motion mode in the Save Point area.

Set the jogging speed percentage to

on the

Operation Panel



NOTE

To change the jogging speed, select

Setting

Jog

to set the speed and acceleration of the

joints, linear rail, or the Cartesian coordinate system, as shown in Figure 5.21.

Figure 5.21 Adjust the jogging speed

NOTICE

Regarding the jogging speed and acceleration in the Joint coordinate system and

Cartesian coordinate system, we recommend that it should be less than 500mm/s if loaded

and that less than 800mm/s if not loaded.

Jog the Dobot Magician in the Cartesian or Joint coordinate system to move the

suction cup close enough to the small cube for picking-up. For example, the

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands