ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 79

Page: 79 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Figure 5.75 Select the DobotStudio to upgrade the Dobot firmware

Click

, as shown in Figure 5.76.

The Dobot firmware upgrade window is displayed.

Figure 5.76 Confirm the firmware upgrade

Click

Confirm

to upgrade the Dobot firmware, as shown in Figure 5.77. When

the upgrade process bar shows 100%, and a short beep sound is heard, it means

that the firmware is upgraded successfully, as shown in Figure 5.78. In this case,

the LED indicator turns from red to green. Then click

Complete

to exit.

Figure 5.77 Click Confirm

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands