ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 63

Page: 63 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Procedure

Press and hold the unlock button

on the Forearm to move the Dobot Magician

to raise and lower the pen nib until it slightly squeezes the paper. You can also jog

the robotic arm in the Cartesian or Joint coordinate system to slowly pull the Z axis

down to a suitable vertical position for writing, as shown in Figure 5.46.

Figure 5.46 Adjust the position of the pen nib



NOTE

The point marked by a red box, as shown in Figure 5.47, corresponds to the position of

the writing and drawing kit of the Dobot Magician. This point changes its position only

within the annular area when the robotic arm moves.

Figure 5.47 The point corresponding to the laser kit of the robotic arm

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands