ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 145

Page: 145 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

140

Figure 5.171 Power button of the stick controller

Table 5.19 lists the functions of buttons on the stick controller.

Table 5.19 Button function

Button

Function

Power button

Turn on stick controller

The stick controller will turn off automatically

Turn on the

peripheral motor

Turn off the peripheral motor off

Switch to Cartesian coordinate system mode

Switch to Joint coordinate system mode

Control the outtake of the air pump

Control the intake of the air pump

Turn off the air pump

Left stick: Front/back



Cartesian coordinate system mode: Dobot

Magician moves

along X-axis in the

positive/negative direction



Joint coordinate system mode: Dobot Magician

rotates

along

J1-axis

the

positive/negative direction

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands