ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 46

Page: 46 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Table 5.9 The Pro mode of the Teaching & Playback function

No.

Description

StepRun:

run a save point each time in the Save points list. Before clicking

StepRun

, please select

a saved point.

Download:

download the Save points list to the Dobot Magician for working in offline mode. For

details, see

5.3 Working in Offline Mode

Check Lost Step:

the Dobot Magician detects if lost-steps occur in its movements. The default

threshold is 5 degrees. It should be at least 0.5 degrees. You can set the threshold by selecting

Setting

Playback

LostStepParam

Check Lost Step

is selected, the robotic arm detects if the stepper motors lose steps when

moving. If unselected, no detection is performed

If the Dobot Magician detects lost-steps, it stops working, and its LED indicator turns red. In this
case, click Home to get a correct reference position

Multiplexed I/O interface:

control the Dobot Magician via the I/O interfaces such as turning on or

off the air pump

ARC Motion Mode

Application Scenarios

The

ARC

motion mode requires three points in an arc to complete the arc movement process.

In the

ARC

motion mode, only the second point and end point are saved while the start point is

determined by the other modes.

Prerequisites

The Dobot Magician has been powered on and connected to your computer.

Procedure

NOTICE

Note the following rules when saving points to prevent the robotic arm from working

outside its normal workspace.



Any two points cannot coincide.



The three points cannot be in the same straight line.



The arc trajectory cannot exceed the Dobot Magician’s normal workspace.

For example the points A, B, and C are on the arc. Point A is the start point; Point B is the

second point; Point C is the end point, as shown in Figure 5.17.

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands