ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 13

Page: 13 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

2.2.4.1

Verifying the DobotStudio

If the DobotStudio is launched and runs properly by double-clicking the desktop shortcut to

this program, it means that it is installed successfully.

2.2.4.2

Verifying the Dobot Magician Driver

If an available COM port is displayed on the upper left corner of the DobotStudio page after

the robotic arm is powered on, as shown in Figure 2.8, the Dobot Magician driver is installed

successfully.

Figure 2.8 An available COM port is displayed

If no COM port is available, check whether the robotic arm driver is successfully installed by

following the steps below.

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands