ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 53

Page: 53 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Working in Offline Mode

Offline mode allows the Dobot Magician to perform the points in the Save points

list previously

downloaded from the DobotStudio without keeping the USB connection established.

Prerequisites



The Dobot Magician has been powered on.



The Dobot Magician has been connected to the DobotStudio.



The points have been saved.

Procedure

The

Question

dialog box is displayed, asking if you want the Dobot Magician to

automatically to go back to its homing point before performing the save points in the

offline mode, as shown in Figure 5.26.

Figure 5.26 Click Download

When the process bar at the bottom of the

DobotStudio

page shows 100% and then

disappears, it means that the download is complete.

NOTICE



Before using offline mode, Dobot Magician needs to be reset by clicking

Home

to make Dobot Magician more accurate. For the details please refer to

Appendix A Dobot Magician Homing Operation

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands