ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 107

Page: 107 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

102

Before printing, you need to test the extruder to check whether the melted filament

flows from the nozzle of the extruder.

The temperature of the extruder should be above 170℃. Dobot Magician will not

start 3D printing until the filament is in the melting state. So you need to heat the

extruder first.

Set the heating temperature to 200℃ on the

Manual Control

tab of the

Repetier

Host

page and click

, as shown in Figure 5.119.

DANGER

The heating rod will produce high temperature up to 250℃, please be careful. Do not let

children play with it alone. The process needs to be monitored when it is running. After

the process is completed, please turn off the equipment promptly.

Figure 5.119 Heat the extruder

Click the extruder feeder when the heating temperature is up to 200℃ and feed

up to10mm-30mm, as shown in Figure 5.120.

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands