ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 108

Page: 108 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

103

Figure 5.120 Extrude filament

If the melted filament flows from the nozzle of the extruder, the extruder is

working properly.

NOTICE

If the filament extrusion is in the opposite direction. Please remove the filament, and turn

the extruder around, then re-push down the filament.



NOTE

During printing, if the distance from Dobot Magician to the printing platform is too large

or too small to paste the first layer, it can lead to the nozzle blockage. For increasing the

stickiness of the first layer, placing a masking paper on the platform is recommended.

Press the

Unlock

key on the Forearm and drag Dobot Magician to make the

printing head contact the surface of the masking paper (The distance between the

printing head and the surface of the masking paper is the thickness of a sheet of

A4 paper), then release the

Unlock

key.

Input command

M415

on the

G-Code

command window and press

Enter

to get

the current coordinates, as shown in Figure 5.121.

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands