Sharp AR-505 Operation Manual Download | Manualshive

Page: 90 / 174

background image

5-4

CHAPTER

5

COPIER TROUBLE?

Misfeed removal

MISFEED REMOVAL

Open the document feeder and gently remove the misfed
original.

●

If the misfed original cannot be easily removed, open the feeding
roller cover. Close the feeding roller cover firmly by pressing in
the middle of the cover after removing the misfed original.

(B)

Unlock the lever and open the transport cover.

Gently remove the misfed original.

Close the transport cover and close the document feeder.

NOTE:
After misfed originals are removed from locations A and/or B, a
message may appear indicating the number of originals which
must be returned to the document feeder tray. Return the

originals and press the START (

) key to resume copying.

Transport cover

«
...
88
89
90
91
92
...
»

Summary of Contents for AR-505















































































































































































Reviews:

No comments

Related manuals for AR-505

imageCLASS MF5770

Brand: Canon Pages: 49

Brand: Toshiba Pages: 122

Brand: Triumph Adler Pages: 163

Brand: Triumph Adler Pages: 211

Brand: Kyocera Pages: 160

Brand: Xerox Pages: 50

Brand: Canon Pages: 362

Brand: Canon Pages: 424

Brand: Canon Pages: 20

C123 Copycentre

Brand: Xerox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands